Welcome to the Australian Ford Forums forum.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact us.

Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated.

Go Back   Australian Ford Forums > Ford Australia Vehicles > Small and Mid Sized Cars > Fiesta, Festiva and Ka

Reply
 
Thread Tools Display Modes
Old 03-02-2020, 04:14 PM   #1
Sandmann
Starter Motor
 
Join Date: Jan 2020
Posts: 2
Default 2009 Fiesta - Aftermarket head unit wiring question

Hi all

Apologies if this has been asked before. I have a 2009 Fiesta Zetec and I'm installing an aftermarket head unit (a Kenwood DDX2019DABS) which has wiring for both a speed sensor wire and the parking brake warning light (I have no idea why). Does anyone know where I can conveniently tap into these wires?

Thanks in advance...
Matt
Sandmann is offline   Reply With Quote Multi-Quote with this Post
Old 04-02-2020, 12:20 PM   #2
Sandmann
Starter Motor
 
Join Date: Jan 2020
Posts: 2
Default Re: 2009 Fiesta - Aftermarket head unit wiring question

Addendum: For any who're interested I recieved a phone call from Kenwood's technical support today and I found out what those connections are for... the Speed Sense wire supports Apple Car Play for navigation when there's no GPS signal available in tunnels etc, and the park brake connector disables the menus when the parking brake's not applied.



Personally I think I'll just be wiring the park brake sensor to the switched +12V supply so it always thinks the brake is on and I can access the menus any time... and unless it's fairly convenient I won't bother with the speed sense since I use an Android phone and I don't give a damn about Apple Car Play.
Sandmann is offline   Reply With Quote Multi-Quote with this Post
Old 04-02-2020, 02:23 PM   #3
73 4V XB
Frankenford pilot
Donating Member1
 
73 4V XB's Avatar
 
Join Date: Feb 2008
Posts: 18,270
Default Re: 2009 Fiesta - Aftermarket head unit wiring question

I think you’ll find the park brake wire can be earthed. When I hooked a DVD unit it had the same thing so you couldn’t watch DVD while driving.
__________________
Cheers Bretto


73 XB GT
Last of the Big Ports
73 4V XB is online now   Reply With Quote Multi-Quote with this Post
Old 04-02-2020, 03:31 PM   #4
Luke Plaizier
Lukeyson
Donating Member1
 
Luke Plaizier's Avatar
 
Join Date: Mar 2005
Location: Maitland, NSW
Posts: 2,586
Default Re: 2009 Fiesta - Aftermarket head unit wiring question

I've just been having a chat about the Speed sensor or VSS signal in an earlier Fiesta regarding Cruise Control.

Does your car have Stability Control or ABS? If so, it is unlikely to have a VSS. On ABS/ESC equipped carsm the vehicle speed is obtained from an ABS sensor, and then fed from ABS to PCM (Powertrain Control Module) via the CAN Bus, which then sends the speed over the CAN bus again to the Instrument Cluster. On cars without ABS/ESC, there is a VSS (Vehicle Speed Sensor) usually somewhere on the Gearbox. That VSS line then feeds direct to a pin on the PCM, which interprets it and broadcasts the speed to the Instrument Cluster. Back in the day, the VSS itself would have fed directly to the instrument cluster, meaning you might have found it in the dashboard somewhere.

But if you have ABS/ESC, there's a very real chance you don't have a VSS line anywhere. In the cruise control world, this means they need to be CAN enabled, and either listen for the speed on the CAN bus, or use OBD2 J1979 standard signalling to constantly query the road speed via the CAN bus.

But if you DID have it, it would likely be found between the transmission and the PCM, all within the engine bay.....


Luke
__________________
If the human brain was simple enough to understand, we'd be too simple to understand it.
Luke Plaizier is offline   Reply With Quote Multi-Quote with this Post
Reply

Thread Tools
Display Modes

Forum Jump


All times are GMT +11. The time now is 09:00 PM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL